- 您现在的位置：买卖IC网 > Sheet目录412 > EZLC-4421 LB (Silicon Laboratories Inc)KIT EZLINK F930/SI4421 LOW BAND
Si4421
14. Wake-Up Timer Command
Bit
15
1
14
1
13
1
12
r4
11
r3
10
r2
9
r1
8
r0
7
m7
6
m6
5
m5
4
m4
3
m3
2
m2
1
m1
0
m0
POR
E196h
The wake-up time period can be calculated by ( m7 to m0 ) and ( r4 to r0 ):
T wake-up = 1.03 · M · 2 R + 0.5 [ms]
Note:
? For continual operation, the ew bit should be cleared and set at the end of every cycle.
? For future compatibility, use R in a range of 0 and 29.
15. Low Duty-Cycle Command
Bit
15
1
14
1
13
0
12
0
11
1
10
0
9
0
8
0
7
d6
6
d5
5
d4
4
d3
3
d2
2
d1
1
d0
0
en
POR
C80Eh
With this command, autonomous low duty-cycle operation can be set in order to decrease the average power consumption in receive
mode.
Bits 7-1 ( d6-d0 ):
The duty-cycle can be calculated by using ( d6 to d0 ) and M. (M is parameter in a Wake-Up Timer Command , see
above). The time cycle is determined by the Wake-Up Timer Command .
duty-cycle= (D · 2 +1) / M · 100%
Bit 0 (en) : Enables the low duty-cycle Mode. Wake-up timer interrupt is not generated in this mode.
Note: In this operation mode, bit er must be cleared and bit ew must be set in the Power Management Command (page 15) .
In low duty-cycle mode the receiver periodically wakes up for a short period of time and checks if there is a valid FSK transmission in
progress. FSK transmission is detected in the frequency range determined by Frequency Setting Command (page 17) plus and
minus the baseband filter bandwidth determined by the Receiver Control Command (page 17). This on-time is automatically
extended while DQD indicates good received signal condition.
When calculating the on-time take into account:
-
-
the crystal oscillator, the synthesizer and the PLL needs time to start, see the AC Characteristics (Turn-on/Turnaround
timings) on page 11
depending on the DQD parameter, the chip needs to receive a few valid data bits before the DQD signal indicates good
signal condition ( Data Filter Command , page 19)
Choosing too short on-time can prevent the crystal oscillator from starting or the DQD signal will not go high even when the received
signal has good quality.
There is an application proposal on page 26. The Si4421 is configured to work in FIFO mode. The chip periodically wakes up and
switches to receiving mode. If valid FSK data received, the chip sends an interrupt to the microcontroller and continues filling the RX
FIFO. After the transmission is over and the FIFO is read out completely and all other interrupts are cleared, the chip goes back to low
power consumption mode.
25
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
F2M03G-KIT-1
KIT EVAL G MOD SNGL (NO OEM BRD)
F2M03M-KIT-1
KIT EVAL M MOD SNGL (NO OEM BRD)
FA10323_K2S-W
LENS FOR LUXEON K2
FA10539_SSS-W
LENS FOR SEOUL P4
FA10643_TINA-M
LENS FOR GOLDEN/PLATINUM DRAGON
FA10644_TINA-D
LENS TINA DIFF 6.5DEG
FA10666_CXP-D
LENS CXP DIFF SQ 16DEG
FA10678_CMC-SS
LENS CMC SMOOTH SPOT MC-E
相关代理商/技术参数
EZLC-4421HB
制造商:Silicon Laboratories Inc 功能描述:EZLink 4421 development kit, 868/915MHz
EZLC-4421LB
制造商:Silicon Laboratories Inc 功能描述:EZLink 4421 development kit, 433MHz
EZLC4431B1-D434
功能描述:射频开发工具 EZLink Kit F930 Si4431 Rev B1 434MHz
RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
EZLC4431B1-D868
功能描述:射频开发工具 EZLink Kit F930 Si4431 Rev B1 868MHz
RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
EZLC-4432 HB
功能描述:射频开发工具 EZLink Fast Prototype Kit Hiband RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
EZLC-4432 HB/LB KIT
制造商:Silicon Laboratories Inc 功能描述:
EZLC-4432 LB
功能描述:射频开发工具 EZLink Fast Prototype Kit Lwband RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
EZLC4432B1-D470
功能描述:射频开发工具 EZLink Kit F930 Si4432 Rev B1 470MHz
RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V